How to Isolate and Stain Mouse Bone Marrow Cells for Flow Cytometry

The protocol below is a general procedure for the isolation, preparation, and staining of mouse bone marrow cells for flow cytometric analysis.


Materials


Protocol

  1. Isolate cells from mouse femora and tibiae by flushing bones with 1 - 3 mL phosphate-buffered saline (PBS) (without Mg2+ and Ca2+) supplemented with 5 mM EDTA plus 1% fetal calf serum. Flushing may be done using a 21 - 26G needle attached to a 1 - 10 mL syringe.
  2. Generate a single-cell suspension by gently triturating the cells through the needle until large clumps are no longer present.
  3. Lyse red blood cells (RBCs) by adding cold ammonium chloride solution and incubating bone marrow cells on ice for 10 minutes.
  4. Following RBC lysis, top up the sample with an appropriate volume of PBS or similar wash buffer, and centrifuge at 300 x g for 5 minutes at room temperature (RT; 15 - 25°C). Resuspend the cell pellet in PBS and filter through a 70 μm filter to remove aggregated cell clumps and debris.
  5. Count the cells in the filtered suspension and dilute to 1 x 107 cells/mL in the same medium. The expected recovery of nucleated cells from both tibiae and femora (i.e. 4 long bones) of a normal male C57Bl/6 mouse is approximately 4 - 5 x 107 cells.
  6. To reduce non-specific binding of fluorescent antibodies, block Fc receptors by incubating cells with anti-CD16/32 (clone 2.4G2) antibody and 10% rat serum for 10 minutes on ice.
  7. For single antibody-stained controls, aliquot 3 x 104 cells per tube and stain with optimized concentrations of individual antibodies in a total volume of ~100 μL.
  8. In parallel, set up FMOs and test samples by aliquoting 2 - 3 x 106 cells per tube and stain with optimized concentrations of antibodies.
  9. Incubate cells for 20 minutes on ice, in the dark.
  10. Wash cells in an appropriate volume of PBS and centrifuge at 300 x g for 5 minutes at RT, then aspirate the supernatant.
  11. Resuspend cells in 100 μL PBS.
  12. Just prior to acquisition, add 1 μg/mL 7-AAD to all samples, except unstained, single antibody-stained, and 7-AAD-FMO controls. Addition of 7-AAD to separate unstained and single antibody-stained controls should be considered if there are many dead or apoptotic cells that can cause increased autofluorescence or non-specific staining.

    Note: This general protocol uses 7-AAD to detect non-viable cells, but other viability dyes such as propidium iodide (PI) or amine-reactive dyes may also be used.
  13. If using compensation beads, stain controls according to the manufacturer’s directions. To provide an optimal fluorescence signal, it is important to titrate the antibody so that the highest staining index is achieved.

  • Document #PR00030
  • Version 1.0.0
  • November 2020


  • Related Resources

    Download this wallchart for a handy overview of the subset hierarchy, including their frequencies and phenotypes.

    Wallchart: Human HSPC Phenotyping

    Learn more about human HSPC subsets with this wallchart which provides a handy overview of the subset hierarchy, including their frequencies and phenotypes.

    Contact STEMCELL Technologies

    Our Customer Service, Sales, and Product and Scientific Support departments in North America are available between 6 am and 5 pm Pacific Time (9 am and 8 pm Eastern Time). One of our representatives will be happy to help you by telephone or email. Please complete the form to contact us by email. A representative will get back to you shortly.
    •  

    StemCell Technologies Inc. and affiliates ("STEMCELL Technologies") does not share your email address with third parties. StemCell Technologies Inc. will use your email address to confirm your identity and send you newsletters, transaction-related emails, promotional and customer service emails in accordance with our privacy policy. You can change your email preferences at any time.